Orafol ORAJET 3751 RA

Description

Orafol ORAJET 3751 RA

Orafol ORAJET 3751 RA
2 Mil Cast Gloss White Inkjet Vinyl with Repositionable Adhesive.
• 8 year outdoor durability.
• Low initial tack.
• Grey, opaque, repositionable, solvent-based, removable adhesive with air-egress; clean removability for up to 4 years.
• 101lb liner.
• Ideal for applications over vehicle wraps and uneven or curved surfaces, rivets and corrugations.
• ORACAL suggests laminating with Oraguard 290, 290F, 293.
• Print Compatibility: Solvent, Eco-Solvent, UV, Latex.

http://www.signwarehouse.com/Miva/PDFs/Media/M_OraJET-3751RA_Specs.pdf

Description
2.25-mil, cast PVC film with a low initial tack adhesive, white gloss surface with RapidAir® technology
Release Paper
101# PE-coated silicone paper featuring an advanced air release technology to facilitate quicker, easier application
Adhesive
Grey, solvent-based, repositionable, permanent low initial tack adhesive can be removed with little or no adhesive residue
for up to four years with heat
Applications
Long-term, irregular surfaces such as outdoor signage, and complex vehicle and fleet graphics

Attention
Recycling Recommendation: Waste class similar to household waste, is to be recycled according to the local regulations.
Surfaces to which the material will be applied must be cleaned thoroughly of dust, grease or any contaminants. Freshly lacquered
or painted surfaces should be allowed to stand for at least three weeks after complete curing. The compatibility of selected
lacquers and paints should be tested by the end-user prior to use.
The statements in this information sheet are based upon our knowledge and practical experience. This data is intended only as a
source of information and is given without any guarantee and does not constitute a warranty. Due to the wide variety of possible
uses and applications, customers should independently determine the suitability of this material for their specific
purpose, prior to use.
For instant access to more information click on the links below
Profiles
http://www.oracal.com/knowledge/icc-profiles.asp
Tech Support
http://www.oracal.com/knowledge/contact-support.asp
Find a Distributor
http://www.oracal.com/distributors/
General Warranty
http://www.oracal.com/_userfiles/File/GeneralWarranty.pdf Revised 11/11
Technical Data
Thickness (without protective paper and adhesive) 2.25 mil
Dimensional Stability (FINAT TM-14) Adhered to steel, no shrinkage in cross direction;
In length, <.004”
Temperature Resistance Adhered to aluminum, -58°F to +212°F, no variation
Fire Behavior (DIN 75200)
Fire Rating
Adhered to steel, self-extinguishing
ASTM E 84-07 Class “A”
Adhesive Power (FINAT TM-1, after 24 h, average) Adhered to stainless steel: 4.1 lb/in
Tensile Strength (DIN EN ISO 527)
Along
Across
Min. 19 MPa
Min. 19 MPa
Elongation at Break (DIN EN ISO 527)
Along
Across
Min. 120%
Min. 120%
Seawaterability (DIN 50 021) Adhered to aluminum, after 100h/73°F, no variation
Shelf Life (68°F/50% relative humidity) 2 years
Minimum Application Temperature 50°F
Available Lengths
Available Widths (inches)
150’ (50-yard)
30, 54, 60
Minimum Life Expectancy (based on accepted application
procedures on vertical surfaces)
8 years (Unprinted)
Recommended Laminates
Oracal recommends that printed film is allowed to dry for at least 24 hours at 70°F (48-72 preferred) before applying a laminate.
ORAGUARD® Series 290, 290F, 293